Ready-to-install rope starter for clockwise rotating Puch E50 engines on your Puch Maxi S / N or Puch Supermaxi LG1 moped / moped. Can only be fitted in conjunction with an original Bosch / Ducati ignition.
Made in Switzerland. Designed for the highest loads and proven in racing.
Fitting:
1. Starter pinion: Clean the flywheel, then screw the counterpart for the cable starter onto the pole wheel (secure with Loctite).
2. Pull-wire starter: Position the starter housing correctly and tap lightly with a plastic hammer until the pull-wire starter is perfectly seated. It can then be screwed into place.
Application:
1. Before starting, pull the cable slowly a few times so that the engine turns over empty (must be done before each start attempt).
2. Pull out the cable starter handle until it engages fully and you encounter resistance. Then pull through in one go.
Tip: Wear gloves! Hold the handle firmly.
Note: The pedal mechanism can no longer be operated as the pedal arms would come into contact with the housing of the pull starter. Therefore, footrests, a longer pedal axle or a pedal axle extension must be fitted.
Other helpful parts for the cable starter conversion such as Loctite, racing gloves, replacement cord, rubber mallet etc. can be found in the accessories section. You can find them in the accessories section.
Exceptional product for the highest demands of the quality brand swiing®.
Details
| Manufacturer | swiing® ingenious parts |
| Material | Steel, Plastic |
| Surface | chrome-plated |
| Ignition system | BOSCH, DUCATI |
| Width | 150 mm |
| Height | 88 mm |
| Number of fixing points | 2 pcs |
| Ø outside | 130 mm |
| Total length | 160 mm |
| Color | Chrome, black-matt |
| Hole spacing | 137.5 mm |
Suitable for the following models
| Puch | E50 |
Accessories & related products
Loctite 243 medium-strength threadlocker 10 ml
Temperature resistance (min.): -75 - 200 °C · Manufacturer: Loctite · Material to be used: Aluminum · Material to be used: Metal · Material to be used: Steel · Contents [ml]: 10 ml · Color: blue · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: May irritate the respiratory tract · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Area of application: Chemistry · Adhesion: medium strength · Gap dimension (max.): 0.01 mm · Type of application: 1K · Alignment time: 600 sec · Breakaway torque (according to material): 3 N/m · Breakaway torque (according to material): 12 N/m · Breakaway torque (according to material): 26 N/m
EUR 24.90
EUR 2’490.00/l
GPO pedal axle with chrome rim | Puch Supermaxi LG1, LG2
Chain pitch: 1/2" x 3/16" · Manufacturer: GPO · Material: Steel · Surface: chrome-plated · Color: Chrome · Number of teeth: 28 pcs · Wavelength from wreath: 41 mm · Wavelength from wreath: 206 mm · Ø outside: 15.9 mm · Ø Outer sprocket: 120 mm · Ø Pedal arm holder: 15.9 mm · Total length: 257 mm · Ø Bearing support: 15.9 mm · Crank (wreath): 7.5 mm
EUR 68.10
Moped fans like you also bought:
Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing
Ø nipple: 3 mm · Nipple length: 5 mm · Manufacturer: Made in Germany · Number of components: 1 pcs · Material: Steel · Surface: galvanized (blue) · Ø Stranded wire: 1.25 mm · Cable length: 2200 mm · Nipple shape: Cylinder · Area of application: Standard
EUR 3.20
Bumm mirror round Inox
Manufacturer: Bumm · Material: Chrome steel (known as Nirosta®) · Material: Steel · Surface: chrome-plated · Color: Chrome · Thread size: M8 · Ø mirror surface: 107 mm · Thread type: M8x1.25 (standard thread) · Ø mirror rod: 8 mm · Mirror rod length: 300 mm · Clamping diameter: 22 mm · Total length: 360 mm
EUR 28.30
swiing® revival side protection screw set black | Puch Maxi S
Manufacturer: swiing® revival parts · Material: Plastic · Material: Steel · Surface: galvanized (blue) · Surface: raw · Color: silver · Thread length: 35 mm · Thread length: 50 mm · Thread type: M5x0.8 (standard thread) · Drive: Slot · Drive: Triangular head · Total length: 47 mm · Total length: 60 mm
EUR 14.70
GPO 44 mm cylinder head tuning | Puch Maxi S, N / X30 NS, NL, N-2AH
Manufacturer: GPO · Material: Aluminum · Camouflaged: Yes · Surface: sandblasted · Width: 125 mm · Total length: 135 mm · Height: 55 mm · Ø cylinder: 44 mm · Candle thread: short · Number of fixing points: 4 pcs · Area of application: Tuning · Hole pattern [mm]: 44 x 44 · Decompressor: No
EUR 48.80
Collection only possible with online purchase and appointment.
