The legendary high-end crankshaft suitable for Sachs 50 (without blower) and 50/3 engines.
The shaft can also be used in the 50/2 (also called 502) and 503 engines with minor adjustments.
High-quality and precisely fitting full-flange crankshaft with polished connecting rod, which has proven itself in various load tests. Designed for use in engines with a large power increase and tested up to 19,000 rpm.
The crankshaft can also be used on Sachs 503 engines, so that the drive wheel does not rub against the housing, it must be shimmed with 1.5 mm spacers. The matching spacers can be found in the accessories section.
The large balancing holes in the cheeks have been sealed with aluminum inserts for maximum pre-compression.
This crankshaft is designed for E15 main bearings.
Dimensions of the crankshaft:
Attention: The width of the needle bearing is 15.2 mm, depending on the piston it may need to be slightly recessed inside.
Installation tip: The transition between the crank webs and the crankpin is provided with a slight radius for reinforcement. In order to be able to distance out cleanly, a 16 x 1 mm spacer washer should be used on the left and right, which lays cleanly over the chamfer and is therefore also perfectly centered. The other spacers can be used normally with Ø 15 mm.
Quality product from the Portuguese manufacturer Rito.
Details
Manufacturer | Rito |
Material | Steel, Aluminum |
Cheek type | Full cheeks |
Crankshaft stroke | 42 mm |
Ø piston pin (B) | 12 mm |
Connecting rod length center-center | 84 mm |
Total length of crankpin on clutch side | 41.5 mm |
Thread length | 7 mm, 9 mm |
Weight | 1026 g |
Total length crankpin ignition side | 63.7 mm |
Ø crank webs | 84.9 mm |
Ø Connecting rod eye | 16 mm |
Ø Bearing seat (clutch side) | 15 mm |
Ø Bearing seat (ignition side) | 15 mm |
Area of application | High End, Racing, Tuning |
Thread type | MF10x1 (fine pitch thread) |
Dimension needle bearing | 12 / 16 x 15.7 mm (axe 12) |
Wide crank webs | 29.8 mm |
Length 1st paragraph | 18.5 mm |
Length 2nd paragraph | 14 mm |
Ø 1st step (on the coupling side) | 15 mm |
Ø 2nd shoulder (on the clutch side) | 12 mm |
Length of shoulder (ignition side) | 37 mm |
Number of gears | 2 pcs |
Suitable for the following models
Sachs | 50 (Fahrtwind, 1.25 / 1.5 hp, DE) 50/2 - L CH (0.8 PS), ML CH (0.8 PS), MB (2.6 PS), MLB (2.6 PS) 50/3 |
Accessories & related products
swiing® ingenious puller L17 / BO15 / E15 shoulder bearing
Width across flats (trigger): 8 mm · Width across flats (trigger): 19 mm · Span: 24 mm · Manufacturer: swiing® ingenious parts · Clamping depth: 10 mm · Peel-off tray: BO15 · Peel-off tray: E15 · Peel-off tray: L17 · Surface: galvanized (blue) · Diameter: 24 mm · Diameter: 40.3 mm · Thread type: M6x1 (standard thread) · Thread type: M8x1.25 (standard thread) · Total length: 120 mm · Number of components: 1 pcs · Area of application: (Dis)assembly tool
EUR 49.90
NSK E15 shoulder ball bearing 15/35/8 (A1149)
Bearing cage: Brass cage ball-guided · Inner ring width: 8 mm · Manufacturer: NSK · Bearing clearance: CN (standard) · Groove ring: No · Material: Brass · Material: Steel · Surface: blank · Bearing type: Shoulder bearing · Width: 8 mm · Stock number: E15 · Ø outside: 35 mm · Ø inside: 15 mm · Area of application: Standard · Ball bearing closed: No · Sachs OEM no.: 0232 017 006 · Pony OEM number: A1149
EUR 28.30
swiing® revival shim set | Sachs 503, 502, 50/2, 50/3
Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Nominal diameter inside: 13 mm · Ø outside: 18 mm · Ø outside: 21 mm · Ø inside: 12.5 mm · Ø inside: 15.2 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.4 mm · Thickness: 0.45 mm · Thickness: 0.5 mm · Thickness: 1 mm
EUR 19.20
swiing crankshaft High End (Version 2.0) | Sachs 503 2AL, 2BL
Manufacturer: swiing · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 42 mm · Connecting rod length center-center: 85 mm · Total length of crankpin on clutch side: 43.5 mm · Total length crankpin ignition side: 63.4 mm · Ø crank webs: 85 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 15 mm · Ø Bearing seat (ignition side): 15 mm · Thread type: MF10x1 (fine pitch thread) · Thread length: 8 mm · Thread length: 11 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 30.1 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 13 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 12 mm · Length of shoulder (ignition side): 35 mm · Number of gears: 2 pcs · Area of application: High End · Area of application: Racing · Area of application: Tuning
EUR 213.50
Not in stock
swiing crankshaft High End (Version 2.0) | Sachs 50/2, 50/3
Manufacturer: swiing · Cheek type: Full cheeks · Crankshaft stroke: 42 mm · Connecting rod length center-center: 85 mm · Total length of crankpin on clutch side: 40.7 mm · Total length crankpin ignition side: 63.4 mm · Ø crank webs: 85 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 15 mm · Ø Bearing seat (ignition side): 15 mm · Thread type: MF10x1 (fine pitch thread) · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 30.1 mm · Weight: 1038 g · Area of application: High End
EUR 213.50
Not in stock
Moped fans like you also bought:
Oil seal NBR 15/30/7 B AS | Sachs 503, 50/2
Temperature resistance (min.): -30 - 100 °C · Simmering type: B - With sheet metal outer casing / one sealing lip. · Manufacturer: Sachs · Material: NBR · Width: 7 mm · Ø outside: 30 mm · Ø inside: 15 mm · Sachs OEM no.: 0250 090 000 · Pony OEM number: A1830
EUR 6.15
NSK E15 shoulder ball bearing 15/35/8 (A1149)
Bearing cage: Brass cage ball-guided · Inner ring width: 8 mm · Manufacturer: NSK · Bearing clearance: CN (standard) · Groove ring: No · Material: Brass · Material: Steel · Surface: blank · Bearing type: Shoulder bearing · Width: 8 mm · Stock number: E15 · Ø outside: 35 mm · Ø inside: 15 mm · Area of application: Standard · Ball bearing closed: No · Sachs OEM no.: 0232 017 006 · Pony OEM number: A1149
EUR 28.30
NSK BO15 shoulder ball bearing 15/40/10 (A4502)
Bearing cage: Brass cage ball-guided · Inner ring width: 10 mm · Manufacturer: NSK · Material: Brass · Material: Steel · Surface: blank · Bearing type: Shoulder bearing · Width: 10 mm · Stock number: BO15 · Ø outside: 40 mm · Ø inside: 15 mm · Area of application: Standard · Ball bearing closed: No · Sachs OEM no.: 0932 007 001 · Pony OEM number: A4502
EUR 28.30
swiing® revival gearbox cover gasket | Sachs 503 AAL, ABL, AB, AC, ADV, 2AL, 2BL (A1888)
Manufacturer: swiing® revival parts · Number of components: 1 pcs · Material: Sealing paper · Color: sand-colored · Width: 130 mm · Thickness: 0.35 mm · Number of fixing points: 6 pcs · Total length: 200 mm · Pony OEM number: A1888 · Sachs OEM no.: 0250 150 000
EUR 6.15
swiing® revival shim set | Sachs 503, 502, 50/2, 50/3
Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Nominal diameter inside: 13 mm · Ø outside: 18 mm · Ø outside: 21 mm · Ø inside: 12.5 mm · Ø inside: 15.2 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.4 mm · Thickness: 0.45 mm · Thickness: 0.5 mm · Thickness: 1 mm
EUR 19.20
Oil seal FPM 15/30/7 B DUO | Sachs 50/2, 503
Simmering type: B DUO - With sheet metal outer casing / two sealing lips. · Ø inside: 15 mm · Ø outside: 30.1 mm · Manufacturer: Sachs · Material: FPM - Fluororubber · Area of application: Standard · Surface: raw · Width: 7 mm · Temperature resistance (min.): -30 - 200 °C · Pony OEM number: A1830 · Sachs OEM no.: 0250 090 000
EUR 8.95
swiing® revival ball bearing countershaft | Sachs 50/2, 50/3, 50/4, 503 2AL/2BL (A2531)
Bearing cage: "-" Sheet steel cage ball-guided · Ø inside: 15 mm · Ø outside: 35 mm · Inner ring width: 25.6 mm · Manufacturer: swiing® revival parts · Bearing clearance: CN (standard) · Material: Steel · Stock number: E15 · Area of application: High End · Area of application: Standard · Bearing type: Deep groove ball bearing · Width: 8 mm · Thread type: MF20.8x1 LH (fine/left-hand thread) · Pony OEM number: A2531 · Sachs OEM no.: 0286 079 105
EUR 56.70